🎀 Free shipping over ₹399 · Made to order in any colour · Handmade with love in Pune

A rider in leathers hanging a black and red full-face helmet on the Adiva Garage mount in a workshop.
The red mount screwed to a concrete wall with bike keys hanging from its lower hook, a CBR650R parked behind.
A black and red full-face helmet lifted towards the mount, with arrows showing the visor port dropping onto the cradle, and keys on the hook below.

Adiva Garage · No. 001

Your helmet
deserves a
wall.

Not the mirror. Not the seat. Not the floor by the door.

Get the mount — ₹249


See it hold
  • 25 gPETG
  • 8 kgbench-tested
  • 2screws

Hang it. Walk away.



[ 01 — Watch ]

Don’t hide
your helmet.

Real footage, no studio. Tap any clip for sound.

Mark it, drill it

Two holes and a driver. That is the whole install.


Snug, not gorilla

The second screw is what stops it rotating.


The lid goes on

Weight on the shell, never on the strap.


Two helmets, one wall

Pillion lid gets its own. Stack them vertically.


Then you forget it exists

Which is the whole idea.



Helmet

Hanger

Smart wall mount solution to keep your helmet safe, organised and always ready to go.


  • Holds upto8 kg

  • Durable& sturdy

  • Easy toinstall

  • Compact& space saving

Shop now

The mount screwed to a workshop wall with keys hanging from its lower hook, a helmet on the shelf behind and a pegboard of tools.

Loaded before it ships

Every batch gets hung with 8 kg on the bench. If it creaks, it doesn’t go in the box.

Out of Pune in 24 hrs

Printed to order, packed the same day. Cash on delivery, and free over ₹500.

Made by someone who rides

Designed, printed and packed by one workshop. Message us and you get the person who made it.

The mount photographed on white — a black body with a red inlay, the round cradle at the top, the AD emboss on the back plate and keys hanging from the lower hook.
25 g
9.5 × 7.1 × 2.0 cm

[ 02 — The mount ]

Twenty-five grams
of stubborn.

A closed loop of PETG that takes the weight on the shell, not the strap. It goes up with two screws, sits flat against the wall, and doesn’t move again.

  • Tested to 8 kg on the bench. Your helmet weighs about 1.5. The margin is the point.
  • PETG — survives a closed garage in summer. PLA sags at 55 °C. A Pune garage in May gets there. This doesn’t.
  • Integrated hook for gloves, keys or a lock. The stuff you put down and then spend ten minutes finding.
  • 2 screws, flat back plate, no rotation. Two points of contact means it can’t swing out of true.

Printed to order in Pune — not pulled off a pallet.

[ 03 — Why the shape ]

A hook is a hook.
This is a cradle.

Hang a helmet off a bent piece of steel and all that weight lands on two centimetres of strap. Come back in a month and the padding has a dent in it. The round arm spreads the load across the rim instead.

Side-by-side comparison: a plain bent metal hook on the left, the Adiva Garage cradle on the right, with icons for smooth rounded cradle, no sharp edges, spreads contact over the shell, won't flatten the padding, 25 g.
Smooth rounded cradleNothing to bite into the shell
No sharp edgesDeburred by geometry, not sandpaper
Spreads contactLoad across the rim, not a point
Won’t flatten paddingThe liner keeps its shape
Fits full-face & openModular, flip-up, half — all of it

[ 04 — Spec sheet ]

The numbers,
without the poetry.

Material
PETG, 100% infill at the arm
Weight
25 g
Tested load
8 kg, static, on the bench
Dimensions
9.5 × 7.1 × 2.0 cm
Fixings
2 screws (wall plugs included)
Wall types
Brick, concrete, drywall, ply, metal shutter
Heat tolerance
Holds shape through an Indian summer garage
Finish
Two-tone, matte, embossed AD
Made in
Pune, to order
Holds up to 8 kg — strong, sturdy, reliable. The mount on a wall with keys on the hook and a motorcycle behind it.

[ 05 — Up in four minutes ]

Drill. Screw. Hang. Done.

  1. 01

    Pick the wall

    Eye level, arm’s reach from where the bike parks. Anywhere you’d naturally put your hand down.

  2. 02

    Two holes

    Mark through the back plate, 6 mm bit, tap the plugs in. Flat back means no fiddling with alignment.

  3. 03

    Two screws

    Snug, not gorilla. The second screw is what stops it rotating under load.

  4. 04

    Hang it

    Helmet on the cradle, gloves on the hook, keys through the loop. Walk away.

[ 06 — Off the print bed ]

Unretouched, unstyled,
on actual walls.

Phone photos from the workshop. No lighting rig, no render. This is what turns up in the box.










[ 07 — Six ways ]

Match the bike.
Or don’t.

Six standard colourways, all two-tone with the black inlay. Tell us the shade at checkout — it’s printed after you order, so it costs us nothing to make yours the right red.

  • Race red
  • Stealth black
  • Paddock white
  • Works blue
  • Hi-vis green
  • Signal orange
Six mounts laid out in red, black, white, blue, green and orange, each with a contrasting black inlay.

[ 08 — Take one home ]

One for you.
One for the
pillion lid.

Everyone who buys one messages a week later asking for a second. We priced the pair so you don’t have to.

  • Wall plugs and screws in the box
  • Ships from Pune in 24 hrs
  • Cash on delivery available
  • Breaks under normal use? We replace it.
Save ₹49

Pair

₹449 ₹498

Two mounts. Yours and the one you’ll be asked for.

Add two — ₹449


[ 09 — From the riders ]

What people said
after a month.

★★★★★

Placeholder review copy — swap this for a real quote you have permission to publish.

Reviewer name · City

★★★★★

Placeholder review copy — swap this for a real quote you have permission to publish.

Reviewer name · City

★★★★★

Placeholder review copy — swap this for a real quote you have permission to publish.

Reviewer name · City

★★★★★

Placeholder review copy — swap this for a real quote you have permission to publish.

Reviewer name · City

[ 10 — Straight answers ]

Before you ask.

Anything not here, message us. You’ll get the person who prints them.

A full-face helmet seated on the mount with keys on the hook below, beside icons for holds up to 8 kg, built-in key hook and easy to install.
Full-face, modular, open-face — stack them vertically and one wall does both lids.

Will it hold my helmet?

Yes. A full-face lid is 1.4–1.8 kg. The mount is bench-tested at 8 kg — about five helmets — and the failure mode we design against is creep over years, not a single load.

It’s 3D printed. Doesn’t that mean weak?

It means printed, which is a process, not a strength rating. This is PETG at full infill through the arm, with the layer lines running across the load rather than along it. The plastic isn’t the limit — your wall plug is.

Will it melt in a closed garage?

No. PLA — what most cheap prints use — starts softening around 55 °C, which a shut garage in May reaches easily. PETG holds well past that. That’s the entire reason we don’t use PLA.

What about drywall or a metal shutter?

Fine on both. Drywall wants the toggle anchors, not the plugs in the box — tell us at checkout and we’ll drop a set in. On a shutter, use two self-tappers.

Does it fit an open-face or a modular?

Yes. The cradle is sized on the rim, and every helmet class shares roughly the same rim. Full-face, flip-up, modular, open-face, and a bicycle helmet at a pinch.

Can I hang the jacket on it too?

You can, and people do — that’s what the 8 kg headroom buys you. The lower hook is meant for gloves, keys or a disc lock, but a wet jacket over the arm won’t trouble it.

How fast does it ship?

Printed to order and out of Pune within 24 hours. Free delivery over ₹500, and cash on delivery is available.

What if it breaks?

Send us a photo. If it failed under normal use, we print you a new one and post it. We’d rather know than argue.

Adiva Garage

Small things,
made properly,
for people who
ride.

Get the mount — ₹249

or two for ₹449

Adiva Garage Mount
₹249 · or two for ₹449

Buy

Scroll to Top